Up to now, we have been implementing the DistinctIP preference with code
in two places:
1. On check-in, the last_net is determined by taking the /24 or /64
(in ResolveIPAndNetwork()) and we store it with the node record.
2. On node selection, a preference parameter defines whether to return
results that are distinct on last_net.
It can be observed that we have never yet had the need to switch from
DistinctIP to !DistinctIP, or from !DistinctIP to DistinctIP, on the
same satellite, and we will probably never need to do so in an automated
way. It can also be observed that this arrangement makes tests more
complicated, because we often have to arrange for test nodes to have IP
addresses in different /24 networks (a particular pain on macOS).
Those two considerations, plus some pending work on the repair framework
that will make repair take last_net into consideration, motivate this
change.
With this change, in the #2 place, we will _always_ return results that
are distinct on last_net. We implement the DistinctIP preference, then,
by making the #1 place (ResolveIPAndNetwork()) more flexible. When
DistinctIP is enabled, last_net will be calculated as it was before. But
when DistinctIP is _off_, last_net can be the same as address (IP and
port). That will effectively implement !DistinctIP because every
record will have a distinct last_net already.
As a side effect, this flexibility will allow us to change the rules
about last_net construction arbitrarily. We can do tests where last_net
is set to the source IP, or to a /30 prefix, or a /16 prefix, etc., and
be able to exercise the production logic without requiring a virtual
network bridge.
This change should be safe to make without any migration code, because
all known production satellite deployments use DistinctIP, and the
associated last_net values will not change for them. They will only
change for satellites with !DistinctIP, which are mostly test
deployments that can be recreated trivially. For those satellites which
are both permanent and !DistinctIP, node selection will suddenly start
acting as though DistinctIP is enabled, until the operator runs a single
SQL update "UPDATE nodes SET last_net = last_ip_port". That can be done
either before or after deploying software with this change.
I also assert that this will not hurt performance for production
deployments. It's true that adding the distinct requirement to node
selection makes things a little slower, but the distinct requirement is
already present for all production deployments, and they will see no
change.
Refs: https://github.com/storj/storj/issues/5391
Change-Id: I0e7e92498c3da768df5b4d5fb213dcd2d4862924
we have two more fields in the database (noise_proto and
noise_public_key) that now need to go into pb.NodeAddress when
returning AddressedOrderLimits.
the only real complication is making sure type conversions between
database types and NodeURLs and so on don't lose this new
pb.NodeAddress field (NoiseInfo). otherwise this is a relatively
straightforward commit
Change-Id: I45b59d7b2d3ae21c2e6eb95497f07cd388d454b3
I don't know why the go people thought this was a good idea, because
this automatic reformatting is bound to do the wrong thing sometimes,
which is very annoying. But I don't see a way to turn it off, so best to
get this change out of the way.
Change-Id: Ib5dbbca6a6f6fc944d76c9b511b8c904f796e4f3
Union query for both reputable and new nodes didn't properly work. The
top level query is required to have an `AS OF SYSTEM TIME` statement as
well.
Change-Id: I8ee6dd5b700c2b1ed2aa562962bfa72be7eec30a
Currently we were duplicating code for AS OF SYSTEM TIME in several
places. This replaces the code with using a method on
dbutil.Implementation.
As a consequence it's more useful to use a shorter name for
implementation - 'impl' should be sufficiently clear in the context.
Similarly, using AsOfSystemInterval and AsOfSystemTime to distinguish
between the two modes is useful and slightly shorter without causing
confusion.
Change-Id: Idefe55528efa758b6176591017b6572a8d443e3d
Initially we duplicated the code to avoid large scale changes to
the packages. Now we are past metainfo refactor we can remove the
duplication.
Change-Id: I9d0b2756cc6e2a2f4d576afa408a15273a7e1cef
Nodes which are offline_suspended will no longer be considered for new
uploads. The current threshold that enters a node into offline
suspension is 0.6. Disqualification for offline suspension is still
disabled.
Change-Id: I0da9abf47167dd5bf6bb21e0bc2186e003e38d1a
Query nodes table using AS OF SYSTEM TIME '-10s' (by default) when on CRDB to alleviate contention on the nodes table and minimize CRDB retries. Queries for standard uploads are already cached, and node lookups for graceful exit uploads has retry logic so it isn't necessary for the nodes returned to be current.
Additionally, this PR changes NewNodeFraction devDefault and testplanet config from 0.05 to 1.
This is because many tests relied on selecting nodes that were reputable based on audit and uptime
counts of 0, in effect, selecting new nodes as reputable ones.
However, since reputation is now indicated by a vetted_at db field that is explicitly set
rather than implied by audit and uptime counts, it would be more complicated to try to
update all of the nodes' reputations before selecting nodes for tests.
Now we just allow all test nodes to be new if needed.
Change-Id: Ib9531be77408662315b948fd029cee925ed2ca1d
What:
Use the github.com/jackc/pgx postgresql driver in place of
github.com/lib/pq.
Why:
github.com/lib/pq has some problems with error handling and context
cancellations (i.e. it might even issue queries or DML statements more
than once! see https://github.com/lib/pq/issues/939). The
github.com/jackx/pgx library appears not to have these problems, and
also appears to be better engineered and implemented (in particular, it
doesn't use "exceptions by panic"). It should also give us some
performance improvements in some cases, and even more so if we can use
it directly instead of going through the database/sql layer.
Change-Id: Ia696d220f340a097dee9550a312d37de14ed2044
Reduce the number of non-methods to reduce funcs in the namespace also
combine a func to slightly condense the code more.
Change-Id: Ifbe728eb8c8ca4c981df648decd259c2097b6b40
