From the name of the function and from the way it is used (only called
in one place, from "storj.io/storagenode/gracefulexit".(*Chore).Run()),
it should not return graceful exits that have already completed.
In particular, this causes a problem in the case that a node has already
completed a graceful exit from one satellite, after which the satellite
was decommissioned and no longer in the "trusted" list. This causes an
error message to show up in the node logs every single minute like
"failed to get satellite address ... satellite \"X\" is untrusted".
https://forum.storj.io/t/error-gracefulexit-service-failed-to-get-satellite-address/11372
This change causes ListPendingExits to list pending exits only, not all
exits.
Correspondingly, the check for whether an exit is already completed, in
(*Chore).Run(), becomes unnecessary and is here removed.
Change-Id: Ia3e9bb3e92be4a32ebcbda0321e3fe61d77deaa8
Make metainfo.RSConfig a valid pflag config value. This allows us to
configure the RSConfig as a string like k/m/o/n-shareSize, which makes
having multiple supported RS schemes easier in the future.
RS-related config values that are no longer needed have been removed
(MinTotalThreshold, MaxTotalThreshold, MaxBufferMem, Verify).
Change-Id: I0178ae467dcf4375c504e7202f31443d627c15e1
A failed test showed the same piece being deleted twice. This happens if the graceful exit completes before a previous piece deletion finishes. This change adds a "wait" on the limiter before executing the delete all step when GE is done.
Change-Id: I1c8c49d1e501c2728c80d4224a4854e742be27da
on node's start checks if any of trusted satellites has GE status "Exited successfully"
if so - trying to delete blobs/satellite folder, so no trash left on SNO.
Change-Id: I566266c84f2a872df54cd01bc2f15a9934f138ed
with 128B/sec, a satellite with 10min default timeout could already
closed its connection to a node even though the node was able to
compelete the transfer.
Change-Id: I6173d6473a62c6d0b0e0a8765c1ae0a5e57b0a08
..before they are transferred to another node and submitted to the
satellite as successful piece transfers, because if we submit an invalid
signature, the node will be marked as a cheater and disqualified
immediately.
These signatures should have been validated when the piece was
originally stored, but bitrot does happen and needn't be cause for an
immediate DQ.
Change-Id: I8b0ebd5812ea8a2e60766005b7251fbb74ef7857
Most places now need the NodeURL rather than the ID and Address
separately. This simplifies code in multiple places.
Change-Id: I52621d8ca52296a8b5bf7afbc1001cf8bfb44239
Currently uploads can cause a lot of IOPS, reduce this by introducing a
in-memory buffer on-top of the file.
Change-Id: I5f4e3e01c0a36258271d180b922107de447bcb59
Instead of providing the database from outside to testplanet create it
inside and then allow wrapping and modifying it. This is more convenient
to use.
Change-Id: I9b8f69e6e0a19ff984b4e2bfe927c9100c77bc6c
this commit updates our monkit dependency to the v3 version where
it outputs in an influx style. this makes discovery much easier
as many tools are built to look at it this way.
graphite and rothko will suffer some due to no longer being a tree
based on dots. hopefully time will exist to update rothko to
index based on the new metric format.
it adds an influx output for the statreceiver so that we can
write to influxdb v1 or v2 directly.
Change-Id: Iae9f9494a6d29cfbd1f932a5e71a891b490415ff
1 transfer with a minimum speed of 128 Bytes was a nice try but it is
way too low. Even a pi3 was able to handle 7 grpc transfers. We have 4
satellites and with 5 concurrent transfers that should be a total of 20
concurrent transfers. Each transfer will have a minimum speed of 5KB/s.
That should give us a better througput and still be Ok on a pi3.
Change-Id: I650a7baf890080901ef70ea3b5636d93009b4e60
A few variables were not renamed to the new standard piecesTotal and
piecesContentSize, so it was unclear which value was being used. These
have been updated, and some comments made more thorough.
Change-Id: I363bad4dec2a8e5c54d22c3c4cd85fc3d2b3096c
This change updates the storagenode piecestore apis to expose access to
the full piece size stored on disk. Previously we only had access to
(and only kept a cache of) the content size used for all pieces. This
was inaccurate when reporting the amount of disk space used by nodes.
We now have access to the total content size, as well as the total disk
usage, of all pieces. The pieces cache also keeps a cache of the total
piece size along with the content size.
Change-Id: I4fffe7e1257e04c46021a2e37c5adc6fe69bee55
With this change RS configuration will be set on satellite. Uplink with
get RS values with BeginObject request and will use it. For backward
compatibility and to avoid super large change redundancy scheme stored
with bucket is not touched. This can be done in future.
Change-Id: Ia5f76fc10c37e2c44e4f7b8754f28eafe1f97eff
Remove direct dependency on uplink.RSConfig, this simplifies
moving the config file without introducing weird dependencies.
Change-Id: I7fd2a145401e0205d7047631df9d2810241efeec
This commit adds functionality to include the space used in the trash
directory when calculating available space on the node.
It also includes this trash value in the space used cache, with methods
to keep the cache up-to-date as files are trashed, restored, and
emptied.
As part of the commit, the RestoreTrash and EmptyTrash methods have
slightly changed signatures. RestoreTrash now also returns the keys that
were restored, while EmptyTrash also returns the total disk space
recovered. Each of these changes makes it possible to keep the cache
up-to-date and know how much space is being used/recovered.
Also changed is the signature of PieceStoreAccess.ContentSize method.
Previously this method returns only the content size of the blob,
removing the size of any header data. This method has been renamed
`Size` and returns both the full disk size and content size of the blob.
This allows us to only stat the file once, and in some instances (i.e.
cache) knowing the full file size is useful.
Note: This commit simply adds the trash size data to the piece size data
we were already collecting. The piece size data is not accurate for all
use-cases (e.g. because it does not contain piece header data); however,
this commit does not fix that problem. Now that the ContentSize (Size)
method returns the full size of the file, it should be easier to fix
this problem in a future commit.
Change-Id: I4a6cae09e262c8452a618116d1dc66b687f59f85
